2759-2290/211-1000 - e!RUNTIME; DNP3-Slave; Single License; Online Activation
- Brand: Wago
- Product Code: 2759-2290/211-1000
Description: Function: The DNP3 Configurator is part of the e!COCKPIT Software. With this license, the DBP3 Protocol can be activated on the slave. The configurator fully supports the DNP3-specific functions of all WAGO telecontrollers. The configurator sets up DNP3 objects while configuring data exchange to the PLC application or I/O modules. The settings can be imported and exported in DNP3 XML device profile format. WAGOs telecontrollers can work as TCP, UDP and serial DNP3 slaves. Cyclical time synchronization of the telecontrol substation (slave) can be performed by the master according to DNP3 Device Profile 1.7.2. In the monitoring direction, the WAGO DNP3 Slave can send digital, analog and count values to the master. Both digital and analog values can be received in the control direction. Analog values can be processed in 16-bit, 32-bit or FLOAT format. Count values can be processed in 16-bit or 32-bit format. Your Benefits: Use the PFC200 Controller as a telecontrol substation (slave) on an DNP3 Control System (master) via TCP, UDP or serially. Create a gateway application to transfer data, e.g., from Modbus® Field Devices to a DNP3 Control System. Use: Enter the license into e!COCKPIT, assign it to a device and load both the license and project into the controller. No other installation steps are required. Technical Data: See the document “e!RUNTIME DNP3 Slave Device Profile” on www.wago.com.
Description: Function: The DNP3 Configurator is part of the e!COCKPIT Software. With this license, the DBP3 Protocol can be activated on the slave. The configurator fully supports the DNP3-specific functions of all WAGO telecontrollers. The configurator sets up DNP3 objects while configuring data exchange to the PLC application or I/O modules. The settings can be imported and exported in DNP3 XML device profile format. WAGOs telecontrollers can work as TCP, UDP and serial DNP3 slaves. Cyclical time synchronization of the telecontrol substation (slave) can be performed by the master according to DNP3 Device Profile 1.7.2. In the monitoring direction, the WAGO DNP3 Slave can send digital, analog and count values to the master. Both digital and analog values can be received in the control direction. Analog values can be processed in 16-bit, 32-bit or FLOAT format. Count values can be processed in 16-bit or 32-bit format. Your Benefits: Use the PFC200 Controller as a telecontrol substation (slave) on an DNP3 Control System (master) via TCP, UDP or serially. Create a gateway application to transfer data, e.g., from Modbus® Field Devices to a DNP3 Control System. Use: Enter the license into e!COCKPIT, assign it to a device and load both the license and project into the controller. No other installation steps are required. Technical Data: See the document “e!RUNTIME DNP3 Slave Device Profile” on www.wago.com.
- Available Quantity: 0
$350.90
System requirements
Other required software | e!COCKPIT version: V1.7 |
Software data
Supported devices | 750-8210: PFC200; G2; 4ETH RS 750-8210/025-000: PFC200; G2; 4ETH RS; T 750-8210/040-000: PFC200; G2; 4ETH RS; XTR 750-8217: PFC200; G2; LTE 2ETH RS 750-8217/025-000: PFC200; G2; LTE 2ETH RS; T |
Delivery
Delivery type | License certificate via email (e!COCKPIT already contains the software itself) |
License type (note) | The single license allows installation on one controller. One license per controller is required. |
License type (note) (2) | A PC with both Internet connection and e!COCKPIT may be required for license activation. |
Manual
Configure DNP3
Configure IEC 60870
System Description
Software ‒ General Product Information
Compliance Search
Environmental Product Compliance 2759-2290/211-1000