750-667/000-003 - Fail-safe 4/4 channel digital input/output; 24 VDC; 2 A; PROFIsafe V2.0 iPar
- Brand: Wago
- Product Code: 750-667/000-003
Description: The 75x-667/000-003 Module is equipped with four power outputs (O1 … O4) and four clock sensitive inputs (I1 … I4). The sensors can be supplied directly with 24 V, or fed by two differently clocked outputs (T1 … T2). The inputs connect potential-free, emergency-off switches with contacts, safety interlock switches, mode selectors, as well as both safety sensors and semiconductor outputs (e.g., light barriers, PLC outputs). The power outputs switch both DC13 resistive and inductive loads with up to a 2A-rated current without requiring any additional external circuit. The power outputs operate in both bipolar (high-side/low-side switching) and unipolar (common potential on one side of the load) modes. The module monitors short circuits, cross circuits and 24 V power supply from separate sources. Both the monitoring and additional safety-relevant parameters (e.g., operating modes, switching off test pulses, discrepancy or filter times) can be configured via WAGO-I/O-CHECK. The configuration tool can be conveniently integrated into engineering systems supporting both CC2 and CC3 tool calling interfaces (TCI). When exchanging modules, parameters are automatically downloaded into the control unit via PROFIsafe-compatible iPar server – depending on settings. The PROFIsafe address can be set using the DIP switch on the side of the module, or via WAGO-I/O-CHECK. The module supports both PROFIsafe V1 (PROFIBUS) and V2 (PROFIBUS, PROFINET) protocols. Safety modules can be arranged in any combination when configuring the fieldbus node. To protect the module against impulse voltages (over-voltage protection per IEC 61000-4-5), a WAGO Filter Module or an external surge filter must be used for the 24V supply voltage. Additional information can be found in the product manual (available in German and English).
Description: The 75x-667/000-003 Module is equipped with four power outputs (O1 … O4) and four clock sensitive inputs (I1 … I4). The sensors can be supplied directly with 24 V, or fed by two differently clocked outputs (T1 … T2). The inputs connect potential-free, emergency-off switches with contacts, safety interlock switches, mode selectors, as well as both safety sensors and semiconductor outputs (e.g., light barriers, PLC outputs). The power outputs switch both DC13 resistive and inductive loads with up to a 2A-rated current without requiring any additional external circuit. The power outputs operate in both bipolar (high-side/low-side switching) and unipolar (common potential on one side of the load) modes. The module monitors short circuits, cross circuits and 24 V power supply from separate sources. Both the monitoring and additional safety-relevant parameters (e.g., operating modes, switching off test pulses, discrepancy or filter times) can be configured via WAGO-I/O-CHECK. The configuration tool can be conveniently integrated into engineering systems supporting both CC2 and CC3 tool calling interfaces (TCI). When exchanging modules, parameters are automatically downloaded into the control unit via PROFIsafe-compatible iPar server – depending on settings. The PROFIsafe address can be set using the DIP switch on the side of the module, or via WAGO-I/O-CHECK. The module supports both PROFIsafe V1 (PROFIBUS) and V2 (PROFIBUS, PROFINET) protocols. Safety modules can be arranged in any combination when configuring the fieldbus node. To protect the module against impulse voltages (over-voltage protection per IEC 61000-4-5), a WAGO Filter Module or an external surge filter must be used for the 24V supply voltage. Additional information can be found in the product manual (available in German and English).
Technical data
Number of digital inputs | 4 |
Number of digital outputs | 4 |
Number of Channels | 8 |
Signal type | Voltage |
Signal type (voltage) | 24 VDC |
Sensor connection | 4 x (Fail-safe input with test pulse) |
Actuator connection | 4 x (fail-safe output with test pulse) |
Input characteristic | clock sensitive |
Input characteristic | Type 1 per IEC 61131 |
Input current per channel for signal (1) typ. | 2.2 |
Output circuit design | Power outputs |
Output current per channel | 2 |
Output current (module) | 8 |
Output current | short-circuit-protected |
Switching frequency (max.) | 50 Hz; Resistive load |
Switching frequency (max.) (2) | 0.1 Hz; Inductive load |
Capacitive load for each channel | O1 … O4; 2.2 µF |
Signal frequency (max.) | 50 |
Load type of switching frequency | Resistive load |
Configuration options | PROFIsafe address adjustable via DIP switch or engineering software |
Supply voltage (system) | 5 VDC; via data contacts |
Current consumption (5 V system supply) | 180 |
Supply voltage (field) | 24 VSELV/PELV DC (-15 … +20 %); via power jumper contacts (power supply via blade contact; transmission via spring contact) |
Current consumption, field supply (module with no external load) | 20 |
Isolation | 500 V system/field |
Indicators | LED (A-D) green/red: Status/Error I1 … I4; LED (I-M) green/red: Status/error O1 … O4; LED (E) red: Group error; LED (F-H) green/red: Diagnostics |
Number of incoming power jumper contacts | 2 |
Number of outgoing power jumper contacts | 2 |
Current carrying capacity (power jumper contacts) | 10 |
Functional safety
Achievable safety classes | SIL 3; Category 4, PL e |
Safety standards | IEC 61508-1 … -7; EN ISO 13849-1; EN 62061 |
Test pulse duration (max.) | 500 |
Test pulse duration (min.) | 0 |
Connection data
Connection technology: inputs / outputs | 16 x CAGE CLAMP® |
Connection type 1 | Inputs/Outputs |
Solid conductor | 0.08 … 2.5 mm² / 28 … 14 AWG |
Fine-stranded conductor | 0.08 … 2.5 mm² / 28 … 14 AWG |
Strip length | 8 … 9 mm / 0.31 … 0.35 inches |
Physical data
Width | 24 mm / 0.945 inches |
Height | 100 mm / 3.937 inches |
Depth | 67.8 mm / 2.669 inches |
Depth from upper-edge of DIN-rail | 60.6 mm / 2.386 inches |
Mechanical data
Mounting type | DIN-35 rail |
Pluggable connector | Fixed |
Material data
Color | yellow |
Housing material | Polycarbonate; polyamide 6.6 |
Fire load | 1.967 |
Weight | 104.4 |
Conformity marking | CE |
Environmental requirements
Ambient temperature (operation) | 0 … +55 °C |
Surrounding air temperature (storage) | -25 … +85 °C |
Protection type | IP20 |
Pollution degree (5) | 2 per IEC 61131-2 |
Operating altitude | 0 … 2000 m / 0 … 6562 ft |
Mounting position | horizontal (standing/lying); vertical |
Relative humidity (without condensation) | 95 |
Vibration resistance | 4g per IEC 60068-2-6 |
Shock resistance | 15g per IEC 60068-2-27 |
EMC immunity to interference | per EN 61000-6-2, marine applications |
EMC emission of interference | per EN 61000-6-4, marine applications |
Exposure to pollutants | Per IEC 60068-2-42 and IEC 60068-2-43 |
Permissible pollutant concentration H2S at a relative humidity < 75% | 10 |
Permissible pollutant concentration SO 2 at a relative humidity < 75% | 25 |
Data sheet
750-667/000-003, 4FDI/4FDO 24V/2A PROFIsafe V2 iPar, data sheet
Manual
System Manual WAGO I/O System 750 / 753
4FDI / 4FDO 2A / 24VDC PROFIsafe V2 iPar
System Manual Series 750/753
Bid Text
750-667/000-003
750-667/000-003
Instruction Leaflet
Gebrauchs- und Montageanleitung
System Description
750/753 Series I/O-System ‒ General Product Information
Functional Safety ‒ General Product Information
Use in Hazardous Environments
Position Paper CB24I of the German Electrical and Electronic Manufacturer’s Association (ZVEI)
Overview on WAGO-I/O-SYSTEM 750 approvals
Additional Information
Disposal; Electrical and electronic equipment, Packaging
SISTEMA library
SISTEMA-Bibliothek
VDMA-Bibliothek
Library
Configuration and Commissioning Software
Safety Editor (SEDI) / 750-66x
CAD data
2D/3D Models 750-667/000-003
CAE data
EPLAN Data Portal 750-667/000-003
WSCAD Universe 750-667/000-003
ZUKEN Portal 750-667/000-003
WSCAD Universe 750-667/000-003
EPLAN Data Portal 750-667/000-003
Device Driver
WAGO USB Service Kabel Treiber / Serie 750 und 857