753-482 - 2-channel analog input; 4 … 20 mA HART
- Brand: Wago
- Product Code: 753-482
Description: This analog input module powers field-side signal conditioners and transmits electrically isolated analog signals to the bus system. The 24 V field supply is derived from the modules power jumper contacts. The shield directly connects to the DIN-rail. At approximately 25 mA, overload protection switches the measurement input to a high-resistance state. Once normal operating conditions resume, the measurement input will automatically switch back. This module powers 2-wire signal conditioners without dedicated power supply. Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image of the coupler or controller (parameterizable). For HART communication with connected intelligent HART field devices, the HART protocol can be mapped in the cyclic process image of the coupler or controller (parameterizable). FDT/DTM device drivers are available for select (programmable) couplers, allowing HART tool routing to the connected HART device.
Description: This analog input module powers field-side signal conditioners and transmits electrically isolated analog signals to the bus system. The 24 V field supply is derived from the modules power jumper contacts. The shield directly connects to the DIN-rail. At approximately 25 mA, overload protection switches the measurement input to a high-resistance state. Once normal operating conditions resume, the measurement input will automatically switch back. This module powers 2-wire signal conditioners without dedicated power supply. Up to 4 HART dynamic variables (PV, SV, TV, QV) per channel can be mapped in the cyclic process image of the coupler or controller (parameterizable). For HART communication with connected intelligent HART field devices, the HART protocol can be mapped in the cyclic process image of the coupler or controller (parameterizable). FDT/DTM device drivers are available for select (programmable) couplers, allowing HART tool routing to the connected HART device.
- Available Quantity: 0
$847.90
Notes
Note | Pluggable connectors and coding fingers (753 Series) are not included. |
Technical data
Number of analog inputs | 2 |
Number of Channels | 2 |
Signal type | Current |
Signal type (current) | 4 … 20 mADC |
Sensor connection | 2 x (2-wire) |
Input filter | parameterizable |
Input filter: parametrizable (channel by channel) | yes |
Input voltage (max.) | 24 V |
Input voltage drop | (I meas < 28 mA): non-linear, overload protected U = 0.9 V + 270 Ω x I meas |
Signal characteristics | Single-ended |
Diagnostics | Wire break, measurement range overflow |
Resolution [bit] | 12 |
Data width | 2 x 2-byte data; 2 x 2-byte data + 2n x 4-byte data (n = number of dynamic variables); 2 x 2-byte data + 6-byte mailbox |
Overvoltage protection | 30 V, reverse polarity protected |
Conversion time (typ. ≤) | 10 |
Measurement error, reference temperature | 25 |
Measurement error, deviation max (upper-range value) ≤± | 0.1 |
Temperature error max. (upper-range value) ≤± | 0.01 |
Line break detection | I meas < 3.10 mA |
Short-circuit detection | I meas > 22 mA |
Configuration options | WAGO-I/O-CHECK |
Supply voltage (system) | 5 VDC; via data contacts |
Current consumption (5 V system supply) | 65 |
Supply voltage (field) | 24 VDC (-25 … +30 %); via power jumper contacts (power supply via blade contact; transmission via spring contact) |
HART devices per channel | 1 device (single-drop, no multi-drop) |
HART modems per channel | 1 modem (no multiplex) |
Isolation | 500 V system/field |
Number of incoming power jumper contacts | 2 |
Number of outgoing power jumper contacts | 2 |
Connection data
Connection technology: inputs / outputs | 8 x CAGE CLAMP® |
Connection type 1 | Inputs/Outputs |
Solid conductor | 0.08 … 2.5 mm² / 28 … 14 AWG |
Fine-stranded conductor | 0.08 … 2.5 mm² / 28 … 14 AWG |
Strip length | 9 … 10 mm / 0.35 … 0.39 inches |
Physical data
Width | 12 mm / 0.472 inches |
Height | 100 mm / 3.937 inches |
Depth | 69.8 mm / 2.748 inches |
Depth from upper-edge of DIN-rail | 62.6 mm / 2.465 inches |
Mechanical data
Mounting type | DIN-35 rail |
Pluggable connector | Pluggable |
Material data
Color | light gray |
Housing material | Polycarbonate; polyamide 6.6 |
Fire load | 0.862 |
Weight | 44.5 |
Conformity marking | CE |
Environmental requirements
Ambient temperature (operation) | 0 … +55 °C |
Surrounding air temperature (storage) | -25 … +85 °C |
Protection type | IP20 |
Pollution degree (5) | 2 per IEC 61131-2 |
Operating altitude | 0 … 2000 m / 0 … 6562 ft |
Mounting position | horizontal (standing/lying); vertical |
Relative humidity (without condensation) | 95 |
Vibration resistance | per IEC 60068-2-6 |
Shock resistance | 15g per IEC 60068-2-27 |
EMC immunity to interference | per EN 61000-6-2 |
EMC emission of interference | per EN 61000-6-3 |
Exposure to pollutants | Per IEC 60068-2-42 and IEC 60068-2-43 |
Permissible pollutant concentration H2S at a relative humidity < 75% | 10 |
Permissible pollutant concentration SO 2 at a relative humidity < 75% | 25 |
Manual
System Manual WAGO I/O System 750 / 753
2-channel, 4-20mA, HART, single-ended
System Manual Series 750/753
Bid Text
753-482
753-482
Additional Information
Disposal; Electrical and electronic equipment, Packaging
System Description
Overview on WAGO-I/O-SYSTEM 750 approvals
750/753 Series I/O-System ‒ General Product Information
Application Note e!COCKPIT
HART Tool Routing via ETHERNET with 750-820x and e!RUNTIME (a116130)
Application Note CoDeSys 2.3
HART Tool Routing via PROFIBUS with 750-833 and 750-333 (a116140)
HART Tool Routing via ETHERNET with
750-820x/750-88x and CODESYS 2.3 (a116120)
CAD data
2D/3D Models 753-482
CAE data
WSCAD Universe 753-482
ZUKEN Portal 753-482
EPLAN Data Portal 753-482
Device Driver
ModbusTCP/ HART Gateway DTM / HART 750-48x, 753-48x
759-360; Profibus/ HART Gateway DTM / HART 750-48x , 753-48x
Compliance Search
Environmental Product Compliance 753-482